Hallo Community

ich möchte gerne 2 externe USB Smargo an die VU+ Solo2 per Gbox.net 807E anschliessen, die internen Karten erkennt es aber lieder erkennt es sie nicht die Karten in den 2 Smargos.



Meine Gbox.cfg Config:

F: { 43 } /dev/ttyUSB0 // rs232 com1 # Hier werden die Reader über com1 angesprochen #
F: { 44 } /dev/ttyUSB1 // rs232 com1 # Hier werden die Reader über com2 angesprochen #


Es kommt folgende Meldung im Trace Log:

--------------------------------------------------------------



internal slot1 opened

internal slot2 opened

detect smartcardreader+ version 1.5

mode 1 frequency 3.69 kernel 0 t-mode 0 egt 0

/dev/ttyUSB0 opened with 1 multicam(s)

mode: any pid

have to init card 1

ATR :

3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50

31 38 30 20 4D 65 72 30 30 30 28

Reset Baudrate = 9600 Baud

Nagravision card DNASP180 Mer000

12 E1 01 A0

Serial (UA) .........

Provider 3411

CaID 1843

DT08 signature ok

Generating new session key on card 1

Camkey 15D0D3DC00E8D5F0...

Working Baudrate = 140625 Baud

cardsystem= 4

card init ok

have to init card 2

ATR : 3F 77 18 00 00 C2 EB 41 02 6C 90 00

Reset Baudrate = 9600 Baud

Viaccess Card

CaID 0500

Serial (UA) .....

Issuer FFF403

Provider00 FFF430 PPUA C4200C82 ISSUER

Provider01 050800 PPUA C4200C82 SRGSSR

Provider02 050810 PPUA C4200C82 Service2

Provider03 050820 PPUA C4200C82 Service3

Provider04 050830 PPUA C4200C82 Service4

Provider05 050840 PPUA C4200C82 Service5

Working Baudrate = 145161 Baud

cardsystem= 3

card init ok

have to init card 3

ATR : 3B 78 12 00 00 54 C4 03 00 8F F1 90 00

Reset Baudrate = 9600 Baud

Cryptoworks card bios version 3

ERROR 01 in file select: Working Baudrate = 19200 Baud

card init FAILED !!!

entering main Loop



Also wie gesagt die internen Karten nimmt es an. Nur leider die per Smargo nicht. Weiss jemand warum?!?





Greeeets

Hallo sorry Community, ich habe den Fehler gefunden!!! Wer evtl. mal das gleiche Problem hat, hier die Lösung:



Gbox.cfg

# gbox config file

# Trace, Debug
# xx yz ; xx=00 no konsole output
# xx yz ; xx=01 konsole output
# xx yz ; y=0 debug output (dont use)
# xx yz ; y=1 no debug output
# xx yz ; z=0 ouput to konsole
# xx yz ; z=1 output to /var/tmp/debug.txt
# xx yz ; z=2 Output to UDP (to capture with gboxt)
Z: { 01 12 } 192.168.0.3 8024

# gbox working mode
# 00 pure Emu
# 01 pure SoftCam (when card inside), Emu (when no card inside)
# 02 pure Net Client
# 03 Mixed mode !!!!! always use this !!!!!
G: { 03 }

# Display ECM messages on Konsole
# 00 dont show any ECMs
# 01 show only valid ECMs
# 02 show valid and bad ECMs with complete data display
# 1x show ca access , display: set ca%d index=%d (pid %X) typ=%d

# 2x Map Nagra Aladin to Betacrypt , use nagra aladin 1801 in betacrypt mode (for UM-I02)
C: { 02 }

# Display EMM messages on Konsole
# 00 dont show any EMMs
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
# 1* Log any tier change on PW-Nagra-17xx cards into /var/keys/pwupdate.log
M: { 02 }

# Auto Update
# 00 AU disable (default)
# 01 AU enable
# 02 AU auto
# 03 AU enable with ua,sa and ga filter !!!!! always use this !!!!!
A: { 02 }

# Key Update
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
U: { 01 }

# Hash pids
# 00 hash all pids, DO NOT USE THIS OPTION, IT IS ONLY FOR TESTING STUFF
# 01 hash only pids with implemented algos and available keys !!!!! always use this
H: { 01 }

# Key files folder
# 00 keyfiles in /var/keys
# 01 keyfiles in /var/tmp
T: { 00 }

# On Screen Display for the Multysystemcam on com1/com2
# 00 No OSD (default)
# 01 display Smartcard messages in Neutrino
# 02 display Smartcard messages in Neutrino new nhttpd format
# 03 display Smartcard messages in Enigma
# 04 display Smartcard messages in Enigma2
O: { 00 } 192.168.0.11

# Logger and NET-mode UDP port Init
# 00 do not init UDP port
# 01 Init UDP port for IP, port, UDP
L: { 04 } 192.168.0.251 7025

# demux, multicam/comport configuration
# example: yz = 0x0A = 00001010 (use com2 with inverted CTS detection line)
# *x ** ; x = device nummber to be used (0= default)
# D* ** ; force use of /proc/bus/gtx for cw write operations (in the dbox2 the gbox writes directly the CWs, 00 is the recommended mode ! No drivers are required) use D* ** ONLY if you have Problems. 0* ** should be prefered !!!
# F* ** ; write CWs in both devices (used for PVR in STB04xxx devices)
# ** y* ; y=0001b (0x1*) use slot1 as Multicam (only on STB04xxx)
# ** y* ; y=0010b (0x2*) use slot2 as Multicam (only on STB04xxx)
# ** y* ; y=0011b (0x3*) use slot1 and slot2 as Multicams (only on STB04xxx)
# ** *z ; z=0001b (0x*1) use com1 as Multicam
# ** *z ; z=0010b (0x*2) use com2 as Multicam
# ** *z ; z=0011b (0x*3) use com1 and com2 as Multicams
# ** yz ; yz=00110011b (0x33) use slot1+slot2+com1+com2 as Multicams
# ** *z ; z=0100b (0x*4) invert CTS detection on com1
# ** *z ; z=1000b (0x*8) invert CTS detection on com2
# V: {00 31} the 2 internal reader + an external reader SC8in1, MCR and 4in1 8in1 addressed
#V: {00 35} the 2 internal reader + an 1 external reader such Smargo, Easy Mouse, Multiprog, Multi Mouse inverted addressed
V: {00 3F} the 2 internal reader + an USB HUB + 2 Smargos addressed
#V: { 00 30 }

# RS232 SSSP mode
# x debug messages, 1=on, 0=off
# y com port to use (0=none, 1=com1, 2=com2)
# R: { 00 }

# Task type
# 00 ** normal mode gbox mode (no season, use Multicam instead)
# 01 ** Season Emulation in a Irdeto allcam chid 0602 nonZ
# 10 ** Season Emulation in a Irdeto allcam chid 1702 nonZ
# 11 ** Season Emulation in a Irdeto allcam chid 1702 Z
# 12 ** Season Emulation in a Irdeto allcam chid 1722 Z
# 13 ** Season Emulation in a Irdeto allcam chid 1762 Z
# ** *1 Com port to use for season emulatiom (1 or 2)
# ** 0* Use CTS for RST detection
# ** 1* Use DCD for RST detection
# ** ** 9600 = Baudrate to be used (working only on dbox2)
# W: { 00 00 } 9600

# =============================================================================
# extra options to override default setting in case you expirience Problems,
# normaly these setings are not required.

# Files, folders, devices
# folder/device comment
# F: { 01 } /var/tmp/pmt.tmp // pmt file
# F: { 02 } /var/tmp/emm.info // key update log file
# F: { 03 } /var/tmp/ecm.info // ecm info file
# F: { 04 } /var/tmp/atack.txt // atack info file
# F: { 08 } 1 // pmt mode (0 - pmt file mode, 1 - pmt socket mode)
# F: { 11 } /var/keys // folder for config files
# F: { 12 } /var/tmp // folder for temporary file
# F: { 13 } /var/tmp // folder for keyfiles
# F: { 21 } /dev/null // ca device
# F: { 22 } /dev/null // dvr device
# F: { 23 } /dev/null // demux device
# F: { 31 } /dev/null // second ca device to write cw's (recording)
# F: { 41 } /dev/sci0 // STB04xxx slot1
# F: { 42 } /dev/sci1 // STB04xxx slot1
F: { 43 } /dev/ttyUSB0 // rs232 com1 # Hier werden die Reader über com1 angesprochen #
F: { 44 } /dev/ttyUSB1 // rs232 com1 # Hier werden die Reader über com2 angesprochen #


# For overclocking freaks, Clocking internal STB04xxx slots with:
# 1=7.80MHz 2=6.30MHz 3=5.25MHz 4=4.50MHz 5=3.94MHz 6=3.50MHz 7=3.15MHz
# Irdeto works fine on 7.8MHz, all other fine on 6.30MHz or 5.25MHz
# The Dream has not a clean clock signal, some cards that are sensitive will
# refuse to work even on 3.5MHz, thats why 3.15MHz is the default value there.
# On other STB04xxx recievers the same cards work with 6.30MHz
# F: { 51 } 02 // irdeto
# F: { 52 } 03 // seca
# F: { 53 } 03 // viaccess
# F: { 54 } 03 // nagra
# F: { 55 } 03 // crypto
# F: { 57 } 03 // conax
# F: { 58 } 03 // nds

# force a name change of the season or sssp rs232 device
# F: { 45 } /dev/ttyS1

# set stay alive ping time in seconds (default is 300)
# F: { A0 } 300

# disable direct serial port I/O access on 80x86cpus (win and linux)
# direct port i/o is used to set unusual Baudrates, if you want to
# a 3.579MHz card in a 6.000MHz reader etc ...
#
# Enabled (A1=0) is the default setting, has always been !!!
#
# Disable (set to 1) it ONLY if you have problems with ioperm or you want
# to use a usb-to-rs232 smartcard reader
F: { A1 } 1

# GboxTwin mode (only for old gbox, in gbox.net disabled)
# this options for the 2nd gbox ONLY
# you must have an extra gbox, gbox_cfg and cwshare.cfg running on /tmp,
# all other files can linked to the org. files
# F: { A6 } 5

# Server Mode
# 0 disable
# 1 enable
# F: { A4 } 1

# descrambler selection by camd.socket private descriptor (0 - index mode, 1 - mask mode), mask mode is default
# F: { AA } 1

# Debug card access output
# 0 disable (default)
# 1 simple CA trace
# 2 extended CA trace (with timing)
# F: { CA } 2







Dann noch die Softcam.cfg

# SoftCam EMM Log configuration
#
# Save EMM data
# 00 Don't save anything (default)
# 01 Save processed EMMs (/var/tmp/emmproc.bin)
# 02 Save rejected EMMs (/var/tmp/emmblock.bin)
# 03 Save both EMMs
L: { 00 }

# Check additional OSC Frequency !!! ONLY FOR DBOX2 !!!
# 00 No Check (default)
# >0 Check on, Value in KHz , example 8MHz=08000
# F: { 0000 }

# Check additional Baurate for ATR !!! ONLY FOR DBOX2 !!!
# 00 No Check (default)
# >0 Check on, Value in bit/s, example 81861
# B: { 0000 }

# Enable TPScrypt Support
# *0 TPScrypt off
# *1 TPScrypt on (default)
# 1* don't use PTS on Viaccess cards
# 2* don't use PTS on Cryptoworks cards
# 3* don't use PTS on Viaccess and Cryptoworks cards
# 4* switch IRD to ICE mode and ICE to IRD mode
Y: { 00 }

# Empty RS232 buffer before writing
# 00 No reset
# 01 Reset Buffer (default)
E: { 01 }

# SoftCam Blocker/Filter definition
#
# 00 = Allow EMM (default for all)
# 01 = Block EMM addressed to:
# all card
# | shared address/provider
# | | unique address/hex_serial
# ----------------------------------
I: { 00 00 00 } Irdeto All SA UA
S: { 00 00 00 } Seca - SA UA
V: { 00 00 00 } Via - SA UA
N: { 00 00 00 } Nagra All SA UA
C: { 00 00 00 } Crypto All SA UA
O: { 00 00 00 } Conax - SA UA
D: { 00 00 00 } NDS All SA UA

# Timeout Definitions AND com1/com2 delays, all delays to be entered in decimal !
#T: { 00 02 02 } ATR timeout (normal*X), instruction timeout (normal*X)
T: { 00 02 01 } ATR timeout (normal*X), instruction timeout (normal*X)

# com1/com2 delays, all delays to be entered in decimal !
#
# Do NOT touch !!!!!!!!!!!!!!!!!!
# all timings should be 0, change only if you have problems.
T: { 01 00000 000 } Irdeto : byte delay (1e-6 s), instruction delay (1e-3 s)
T: { 02 00000 000 } Seca
T: { 03 00000 000 } Viaccess
T: { 04 00000 000 } Nagra
T: { 04 00002 000 } Nagra
T: { 05 00000 000 } CryptoWorks
T: { 06 00000 000 } Geldkarte
T: { 07 00000 000 } Conax
T: { 08 00000 000 } NDS
T: { 09 00000 000 } Dreamcrypt/Firecrypt



P.s.: Kann nur jedem die VU+ Solo2 und auch die VU+ SoloSE mit dem Blackhole Image inkl. CCcam, OSCam, Gbox.net und Scam empfehlen ;-). Mit der Gbox.net 807E Multituner läuft es prima...hehe Was ich auch noch empfehle ist die Android App VU+ Player, mit der kann man die VU+ Boxen sehr gut steuern :-)))





Viel Spass

Gbox.cfg:

Z: { 01 12 } 192.168.0.3 8024

G: { 03 }

C: { 02 }

M: { 02 }

A: { 02 }

U: { 01 }

H: { 01 }

T: { 00 }

O: { 00 } 192.168.0.11

L: { 04 } 192.168.0.251 7025

V: {00 3F} the 2 internal reader + an USB HUB + 2 Smargos addressed

F: { 43 } /dev/ttyUSB0 // rs232 com1 # Hier werden die Reader über com1 angesprochen #

F: { 44 } /dev/ttyUSB1 // rs232 com1 # Hier werden die Reader über com2 angesprochen #

F: { A1 } 1





Softcam.cfg:

L: { 00 }

Y: { 00 }

E: { 01 }

I: { 00 00 00 } Irdeto All SA UA

S: { 00 00 00 } Seca - SA UA

V: { 00 00 00 } Via - SA UA

N: { 00 00 00 } Nagra All SA UA

C: { 00 00 00 } Crypto All SA UA

O: { 00 00 00 } Conax - SA UA

D: { 00 00 00 } NDS All SA UA

T: { 00 02 01 } ATR timeout (normal*X), instruction timeout (normal*X)

T: { 01 00000 000 } Irdeto : byte delay (1e-6 s), instruction delay (1e-3 s)

T: { 02 00000 000 } Seca

T: { 03 00000 000 } Viaccess

T: { 04 00000 000 } Nagra

T: { 04 00002 000 } Nagra

T: { 05 00000 000 } CryptoWorks

T: { 06 00000 000 } Geldkarte

T: { 07 00000 000 } Conax

T: { 08 00000 000 } NDS

T: { 09 00000 000 } Dreamcrypt/Firecrypt