Hi All,

just bought the JSC Irdeto card to watch sports on the vu+ with VTI 4.1

So was looking for a step by step tutorial on how to get it running, been searching the internet the whole day without luck. the ones I found are for advanced users.

appropriate if anyone can shed more light.

by the way, when I go under setup->common interface I see nothing. Same thing under the common interface Assignment, i only see slot1/2 no module found!

PS. installed Oscam 1.20-Cccam and Scam 3.59

Thanks.

thanks BigGyros , I tried all of that today. nothing happens.

Scam is green and show up when I move between channels as well.

But is it normal that under setup->common interface I see nothing!

Also a stupid question, when you insert the card should the chip be on top or bottom, i tried both. one side has the arrow and the other side the chip.

thanks again.

The card is brand new, I did the registration and sent the activation signal.

regarding the CCcam I removed the one I had before with the Oscam and re installed the CCcam 2.3.0 for vti panel.

but where should I add the below lines, searched for CCcam and found one but was not a text file!

Just for info, the file/config I had before was: (I just copied it from the internet)


######################################################################
# friends #
######################################################################
f:user pass

######################################################################
# connections #
######################################################################
c:hostname port user pass

####################################################################################
# newcamd #
####################################################################################
n:hostname port user pass 01 02 03 04 05 06 07 08 09 10 11 12 13 14

######################################################################
# other config settings #
######################################################################

server listen port : 23000
allow telnetinfo: Yes
allow webinfo: Yes
webinfo username : User
webinfo password : Pass
telnetinfo username : User
telnetinfo password : Pass
telnetinfo listen port : 16000
webinfo listen port : 16001
osd username :user
osd password :pass
show timing : No
debug : No
newcamd conf :no
disable emm : No
extra emm level : No
emm threads : 1
mini osd : No
softkey file : /var/keys/softcam.key
autoroll file : /var/keys/autoroll.key
#static cw file : /var/keys/constant.cw
caid prio file : /var/etc/cccam.prio
#log warnings : /tmp/warnings.txt
providerinfo file : /var/etc/cccam.providers
channelinfo file : /var/etc/cccam.channelinfo

smartcard clock frequency: /dev/sci0 7800000
camkey: /dev/sci0 11 22 33 44 55 66 77 88
camdata: /dev/sci0 11 22 33 44 55 66 77 88 99 aa bb cc dd ee ff
try all chids : /dev/sci0

Web interface was working before but nothing active, empty fields!

the card is on the first upper slot direct into the receiver without a module!

thanks.

OK, I replaced the part below with yours. nothing happens.

Connected clients: 0
0 ACTIVE CLIENTS IN LAST 20 SECONDS
+---------+---------------+------------+------------+-----+-----+--------+----------------------+
| Username| Host | Connected | Idle time | ECM | EMM | Version| Last used share |
+---------+---------------+------------+------------+-----+-----+--------+----------------------+
+---------+---------------+------------+------------+-----+-----+--------+----------------------+

+---------+---------------------------------------+
| Username| Shareinfo |
+---------+---------------------------------------+
+---------+---------------------------------------+


Available shares: 1

+----------------------+--------+----+-------+----------+-------+-------+
| Host | Type |Caid| System| Providers|Uphops | Nodes |
| | | | | |Maxdown| |
+----------------------+--------+----+-------+----------+-------+-------+
|/dev/sci1 |sci | 603|irdeto |0,1,2,3 |0 11 | |
+----------------------+--------+----+-------+----------+-------+-------+


Available providers:

+----+----------+--------------+------+
|Caid| Provider | Provider Name| System|
+----+----------+--------------+------+
| 603| |Unknown |irdeto|
| 603| 1|Unknown |irdeto|
| 603| 2|Unknown |irdeto|
| 603| 3|Unknown |irdeto|
+----+----------+--------------+------+


card reader /dev/sci0
no or unknown card inserted

card reader /dev/sci1
handled 0(0) ecms and 0(0) emms

Irdeto card
Caid 603 ACS 6 QAT
Cardserial xxxxxxxxxx
Provider 00 000b00
Provider 01 000b00
Provider 02 000b00
Provider 03 01ff00

just did a signal refresh, but still no picture!


card reader /dev/sci0
no or unknown card inserted

card reader /dev/sci1
handled 237(0) ecms and 539(538) emms <---- this is changing now!

Irdeto card
Caid 603 ACS 6 QAT
Cardserial
Provider 00 000b00
Provider 01 000b00
Provider 02 000b00
Provider 03 01ff00
Chid 014D - date 0x11be valid 0x3

maybe there's something wrong with the config file. i just copied it without modifications!

thanks,

Oh, sorry just saw your post!

sorry cant use the other slot since it needs a PCMCI card I guess.

but i changed the sci numbering from 0 to 1 but now i cant see any emms anymore!

card reader /dev/sci1
handled 0(0) ecms and 0(0) emms

Irdeto card
Caid 603 ACS 6 QAT
Cardserial €*„*„*
Provider 00 000b00
Provider 01 000b00
Provider 02 000b00
Provider 03 01ff00
Chid 014D - date 0x11be valid 0x3


Config:

# smartcard clock frequency: /dev/sci1 7800000
# camkey: /dev/sci1 11 22 33 44 55 66 77 88
# camdata: /dev/sci1 11 22 33 44 55 66 77 88 99 aa bb cc dd ee ff
# try all chids : /dev/sci1

SMARTCARD CLOCK FREQUENCY: /dev/sci1 6000000
CAMKEY : /dev/sci1 00 00 00 00 00 00 00 00
CAMDATA : /dev/sci1 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
TRY ALL CHIDS : /dev/sci1

Many many thanks, its working now, not sure why, bit it needed some time I guess.

just a side note, I can get all the channels from +1 to +8 without issues. but some how I cant get +9, +10, hd1 and hd2 is that some how related?

I can see the progress bar showing % and info but cant get the picture.

I called JSC and they gave me the same frequency. but they asked what type of receiver I'm using and recommended humax or so...

Thanks.

by the way I'm on Nile sat.

Done, waited for 15 minutes then it came.