hi forum, i have a Vu uno 4k, that never gets a picture on screen when beeing turned on.
ive hooked the box up to a serial port and i get this output: (on power up)
Spoiler anzeigen
and then nothing more happens.
if i try with a USB update.. the following happens:
See attached txt file.
it seems that my internal "disk" is somehow corrupt, any idea to get this box up and running again? can i run a boot disk on an external usb? and ignore the internal "disk"
thanks for any comments.
ive hooked the box up to a serial port and i get this output: (on power up)
CPU 01
BCM74390011
PRID07252111
v1.21
RR:00000003
BFW
seclib-1.9
BBL v1.0.1
AVS init...
AVS init OK
AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a002b00
AVS load_code offset =00051000
LOADED
AVS: overtemp mon ON
single board
select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2500
MEMSYS-STD
SHMOO 02010100 BLD:exported HW:hpf0_b1p6 V:2.1.1.0
MCB: FLEX
AVS start:status=000000ff
STB: Current voltage=00000381(897)
temperature=00009dd7(40407)
PV=00000345(837)
MV=00000382(898)
AVS FW rev=30333278 [0.3.2.x]
OK
DDR0: !@ ffe0e780 <= ffe0df10 MEMSYS-0 @ f1100000 OK
DDR1: =@ ffe0e780 <= ffe0df10 MEMSYS-1 @ f1180000 OK
Sdram Scramble OTP = 0x00000001
Sdram Scramble OK
select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 1b25252b
BFW load mode OTP = 0x0000000f
bfw_hash_locked = 0x00000000
BFW key3 OK, BFW load OK
BFW v4.1.5
COPY CODE... DONE
MICH: disable success
SSBL
SEC: jtag debug status: 000000af
PINMUX
CACHE FLUSH OK
MMU ON
CACHE FLUSH OK
_fbss 0705dfa0
_ebss 07062cd8
_end 07062cf8
HEAP @ 07100000
STACK @ 09200000
ARCH: CONFIG OK
CLR BSS 0705dfa0 to 07062cd8 OK
CLR SRAM OK
CACHE FLUSH OK
CPU CLKSET OK
GO!
,/
,'/___, BOLT v1.21 v1.21 LOCAL BUILD
.'__ ,' (2016-10-07 21:32:28 Vuplus team)
/,' Copyright (C) 2016 Broadcom
/'
Board: UNO4K
SYS_CTRL: product=72521, family=7439b1, strap=000000b2,
otp @ 0xf0404030 = 0x822000e0: en_cr(0x00000060) en_testport(0x00000080) macrovision_disable(0x02000000) moca_disable(0x80000000) rv9_disable(0x00200000)
otp @ 0xf0404034 = 0x00000021: moca2_disable(0x00000001) rfm_disable(0x00000020)
CPU: 2x B15 [420f00f3] 1719 MHz
SCB: 432 MHz
DDR0 @ 1067MHz, DDR1 @ 1067MHz
RESET CAUSE: 0x000003 main_chip_input power_on (2 of 23 possible causes)
CS0: SFDP SPI, 4MB, 64kB blocks, 64kB erase block, 256B pages
EMMC1: transfer complete timed out, intr: 0x0
Command 17 failed
CS1: NAND: unrecognized ID: 0xffffffff 0xffffffff
RTS0: 0x1101004, 256 clients, ok
RTS1: 0x1181004, 256 clients, ok
BOX MODE: 5
SPLASH: starting
SPLASH BMEM init @ 40000000
SPLASH BMEM init @ c0000000
SPLASH: bad file 'emmcflash0.splash'
SPLASH: load failed
AVS: park check
AVS: temperature monitoring enabled
AVS: STB: V=0.897V, T=+41.381C, PV=0.837V, MV=0.898V, FW=30333278 [0.3.2.x]
USB otp=00000040
boot device name [flash0.bolt]
waiting for usb...done
checking usb
No Priority Usb
checking front key
readFrontKey 0 0
Check ignore.update file
Checking usbdisk0:/vuplus/uno4k/ignore.update......NO
Check force.update file
Checking usbdisk0:/vuplus/uno4k/force.update......NO
bolt update ...Checking usbdisk0:/vuplus/uno4k/bolt_auto.bin......NO
Checking usbdisk0:/vuplus/uno4k/rootfs.tar.bz2......NO
....NO
Checking usbdisk0:/vuplus/uno4k/splash_auto.bin......NO
Checking usbdisk0:/vuplus/uno4k/kernel_auto.bin......NO
1000 Mbps Full-Duplex
Device eth0: hwaddr 00-1D-EC-0F-D4-96, ipaddr 192.168.1.137, mask 255.255.255.0
gateway 192.168.1.1, nameserver 192.168.1.1, domain localdomain
DHCP server 192.168.1.1, DHCP server MAC 44-D9-E7-95-E5-4F
Loader:zimg Filesys:tftp Dev:(null) File:emmcflash0.kernel: Options:root=/dev/mmcblk0p4 rootfstype=ext4 rootflags=data=journal rootwait rw vmalloc=664m bmem=656m@352m bmem=583m@2473m
Could not load : Host name unknown
BOLT>
BCM74390011
PRID07252111
v1.21
RR:00000003
BFW
seclib-1.9
BBL v1.0.1
AVS init...
AVS init OK
AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a002b00
AVS load_code offset =00051000
LOADED
AVS: overtemp mon ON
single board
select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2500
MEMSYS-STD
SHMOO 02010100 BLD:exported HW:hpf0_b1p6 V:2.1.1.0
MCB: FLEX
AVS start:status=000000ff
STB: Current voltage=00000381(897)
temperature=00009dd7(40407)
PV=00000345(837)
MV=00000382(898)
AVS FW rev=30333278 [0.3.2.x]
OK
DDR0: !@ ffe0e780 <= ffe0df10 MEMSYS-0 @ f1100000 OK
DDR1: =@ ffe0e780 <= ffe0df10 MEMSYS-1 @ f1180000 OK
Sdram Scramble OTP = 0x00000001
Sdram Scramble OK
select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 1b25252b
BFW load mode OTP = 0x0000000f
bfw_hash_locked = 0x00000000
BFW key3 OK, BFW load OK
BFW v4.1.5
COPY CODE... DONE
MICH: disable success
SSBL
SEC: jtag debug status: 000000af
PINMUX
CACHE FLUSH OK
MMU ON
CACHE FLUSH OK
_fbss 0705dfa0
_ebss 07062cd8
_end 07062cf8
HEAP @ 07100000
STACK @ 09200000
ARCH: CONFIG OK
CLR BSS 0705dfa0 to 07062cd8 OK
CLR SRAM OK
CACHE FLUSH OK
CPU CLKSET OK
GO!
,/
,'/___, BOLT v1.21 v1.21 LOCAL BUILD
.'__ ,' (2016-10-07 21:32:28 Vuplus team)
/,' Copyright (C) 2016 Broadcom
/'
Board: UNO4K
SYS_CTRL: product=72521, family=7439b1, strap=000000b2,
otp @ 0xf0404030 = 0x822000e0: en_cr(0x00000060) en_testport(0x00000080) macrovision_disable(0x02000000) moca_disable(0x80000000) rv9_disable(0x00200000)
otp @ 0xf0404034 = 0x00000021: moca2_disable(0x00000001) rfm_disable(0x00000020)
CPU: 2x B15 [420f00f3] 1719 MHz
SCB: 432 MHz
DDR0 @ 1067MHz, DDR1 @ 1067MHz
RESET CAUSE: 0x000003 main_chip_input power_on (2 of 23 possible causes)
CS0: SFDP SPI, 4MB, 64kB blocks, 64kB erase block, 256B pages
EMMC1: transfer complete timed out, intr: 0x0
Command 17 failed
CS1: NAND: unrecognized ID: 0xffffffff 0xffffffff
RTS0: 0x1101004, 256 clients, ok
RTS1: 0x1181004, 256 clients, ok
BOX MODE: 5
SPLASH: starting
SPLASH BMEM init @ 40000000
SPLASH BMEM init @ c0000000
SPLASH: bad file 'emmcflash0.splash'
SPLASH: load failed
AVS: park check
AVS: temperature monitoring enabled
AVS: STB: V=0.897V, T=+41.381C, PV=0.837V, MV=0.898V, FW=30333278 [0.3.2.x]
USB otp=00000040
boot device name [flash0.bolt]
waiting for usb...done
checking usb
No Priority Usb
checking front key
readFrontKey 0 0
Check ignore.update file
Checking usbdisk0:/vuplus/uno4k/ignore.update......NO
Check force.update file
Checking usbdisk0:/vuplus/uno4k/force.update......NO
bolt update ...Checking usbdisk0:/vuplus/uno4k/bolt_auto.bin......NO
Checking usbdisk0:/vuplus/uno4k/rootfs.tar.bz2......NO
....NO
Checking usbdisk0:/vuplus/uno4k/splash_auto.bin......NO
Checking usbdisk0:/vuplus/uno4k/kernel_auto.bin......NO
1000 Mbps Full-Duplex
Device eth0: hwaddr 00-1D-EC-0F-D4-96, ipaddr 192.168.1.137, mask 255.255.255.0
gateway 192.168.1.1, nameserver 192.168.1.1, domain localdomain
DHCP server 192.168.1.1, DHCP server MAC 44-D9-E7-95-E5-4F
Loader:zimg Filesys:tftp Dev:(null) File:emmcflash0.kernel: Options:root=/dev/mmcblk0p4 rootfstype=ext4 rootflags=data=journal rootwait rw vmalloc=664m bmem=656m@352m bmem=583m@2473m
Could not load : Host name unknown
BOLT>
and then nothing more happens.
if i try with a USB update.. the following happens:
See attached txt file.
it seems that my internal "disk" is somehow corrupt, any idea to get this box up and running again? can i run a boot disk on an external usb? and ignore the internal "disk"
thanks for any comments.
Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von hgdo ()