[Erledigt] Ultimo 4k Schweizer Sender mit Viacess Modul

This site uses cookies. By continuing to browse this site, you are agreeing to our Cookie Policy.

  • Ist natürlich deine Entscheidung, aber weshalb soll Easymouse keine Alternative sein?

    Bringt ja nur Vorteile:
    1.) löst dein Problem mit dem Modul, da nicht mehr notwendig
    2.) Die Karte kann im HS betrieben werden, was ja mit Modul nur sehr eingeschränkt möglich ist. (streamen)
    3.) Aufnehmen (entschlüsselt) und parallel schauen
  • Das Teil hat auch keine neue ci0.xml oder ci1.xml unter /etc/enigma2 angelegt
    VU+ Ultimo mit 20 LNB T90 8°W bis 31,5O 85er für 39°,42°,45° O, 85er für 22,5, 24,5 u 30°W, 65er für 12,5W, 110er für 28,2°O

    The post was edited 1 time, last by Tiger02 ().

  • sollte ich die box nochmal flashen?
    Geht srf mit der easymouse und Gbox
    VU+ Ultimo mit 20 LNB T90 8°W bis 31,5O 85er für 39°,42°,45° O, 85er für 22,5, 24,5 u 30°W, 65er für 12,5W, 110er für 28,2°O
  • @'Buko,
    läuft in deiner Ultimo 4k die HD+ Karte im CI slot?
    VU+ Ultimo mit 20 LNB T90 8°W bis 31,5O 85er für 39°,42°,45° O, 85er für 22,5, 24,5 u 30°W, 65er für 12,5W, 110er für 28,2°O
  • Problem gelöst:
    ORF und SRF im Kartenleser mit Gbox, die HD+Programme über CI+Modul. CI+ Modul in Slot 1 gesteckt auf RTL HD geschaltet und nach 10 Sekunden war die Sache hell
    VU+ Ultimo mit 20 LNB T90 8°W bis 31,5O 85er für 39°,42°,45° O, 85er für 22,5, 24,5 u 30°W, 65er für 12,5W, 110er für 28,2°O

    The post was edited 1 time, last by Tiger02 ().

  • Tiger02 wrote:

    Geht srf mit der easymouse und Gbox
    ja geht - softcam.cfg einen 3. Reader Slot anlegen und in der gbox.cfg aktiv setzen
    softcam.cfg
    Display Spoiler


    ########################################################################################
    #
    # Softcam settings (OLD)
    #
    ########################################################################################
    #
    # SoftCam EMM Log configuration
    #
    # Save EMM data
    # 00 Do not save anything (default)
    # 01 Save processed EMMs (/var/tmp/emmproc.bin)
    # 02 Save rejected EMMs (/var/tmp/emmblock.bin)
    # 03 Save both EMMs
    L: { 00 }


    # Check additional OSC Frequency !!! ONLY FOR DBOX2 !!!
    # 00 No Check (default)
    # 01 Check on, Value in KHz , example 8MHz=08000
    F: { 0000 }


    # Check additional Baurate for ATR !!! ONLY FOR DBOX2 !!!
    # 00 No Check (default)
    # 01 Check on, Value in bit/s, example 81861
    B: { 0000 }


    # Enable TPScrypt Support
    # 00 TPScrypt off
    # 01 TPScrypt on (default)
    # 1* don't use PTS on Viaccess cards
    # 2* don't use PTS on Cryptoworks cards
    # 3* don't use PTS on Viaccess and Cryptoworks cards
    # 4* use ICE on Cryptoworks cards
    Y: { 01 }


    # Empty RS232 buffer before writing
    # 00 No reset
    # 01 Reset Buffer (default)
    E: { 01 }


    # SoftCam Blocker/Filter definition
    #
    # 00 = Allow EMM (default for all)
    # 01 = Block EMM addressed to:
    # all card
    # | shared address/provider
    # | | unique address/hex_serial
    # ----------------------------------
    I: { 00 00 00 } Irdeto All SA UA
    V: { 00 00 00 } Via - SA UA
    S: { 00 00 00 } Seca - SA UA
    N: { 00 00 00 } Nagra All SA UA
    C: { 00 00 00 } Crypto All SA UA
    O: { 00 00 00 } Conax - SA UA
    D: { 01 01 01 } NDS All SA UA


    # Timeout Definitions AND com1/com2 delays, all delays to be entered in decimal !
    T: { 00 02 02 } ATR timeout (normal*X), instruction timeout (normal*X)
    T: { 01 00000 000 } Irdeto : byte delay (1e-6 s), instruction delay (1e-3 s)
    T: { 02 00000 000 } Seca
    T: { 03 00000 000 } Viaccess
    T: { 04 00000 000 } Nagra
    T: { 05 00000 000 } CryptoWorks
    T: { 06 00000 000 } Geldkarte
    T: { 07 00000 000 } Conax
    T: { 08 00000 000 } NDS


    [generic]
    reset_rs232_buffer = 1


    [slot-1]
    disable_pts = 0
    enable_ice = 0
    alternative_frequency = 0
    alternative_baudrate = 0
    # ungeblockte Karte z.B. HD+
    enable_unique_emm = 1
    enable_shared_emm = 1
    enable_global_emm = 1
    block_unique_emm = 0
    block_shared_emm = 0
    block_global_emm = 0
    block_user_emm = 0
    save_processed_emm = 0
    save_rejected_emm = 0


    [slot-2]
    disable_pts = 0
    enable_ice = 0
    alternative_frequency = 0
    alternative_baudrate = 0
    # ungeblockte Karte z.B. HD+
    enable_unique_emm = 1
    enable_shared_emm = 1
    enable_global_emm = 1
    block_unique_emm = 0
    block_shared_emm = 0
    block_global_emm = 0
    block_user_emm = 0
    save_processed_emm = 0
    save_rejected_emm = 0


    [slot-3]
    disable_pts = 0
    enable_ice = 0
    alternative_frequency = 0
    alternative_baudrate = 0
    # ungeblockte Karte z.B. HD+
    enable_unique_emm = 1
    enable_shared_emm = 1
    enable_global_emm = 1
    block_unique_emm = 0
    block_shared_emm = 0
    block_global_emm = 0
    block_user_emm = 0
    save_processed_emm = 0
    save_rejected_emm = 0


    gbox.cfg
    Display Spoiler


    # gbox config file


    # Trace, Debug
    # xx yz ; xx=00 no konsole output
    # xx yz ; xx=01 konsole output
    # xx yz ; y=0 debug output (dont use)
    # xx yz ; y=1 no debug output
    # xx yz ; z=0 ouput to konsole
    # xx yz ; z=1 output to /var/tmp/debug.txt
    # xx yz ; z=2 Output to UDP (to capture with gboxt)
    Z: { 01 01 } 192.168.1.2 8024


    # gbox working mode
    # 00 pure Emu
    # 01 pure SoftCam (when card inside), Emu (when no card inside)
    # 02 pure Net Client
    # 03 Mixed mode !!!!! always use this !!!!!
    G: { 03 }


    # Display ECM messages on Konsole
    # 00 dont show any ECMs
    # 01 show only valid ECMs
    # 02 show valid and bad ECMs with complete data display
    C: { 01 }


    # Display EMM messages on Konsole
    # 00 dont show any EMMs
    # 01 show only valid EMMs
    # 02 show valid and bad EMMs with complete data display
    # 1* Log any tier change on PW-Nagra-17xx cards into /var/keys/pwupdate.log
    M: { 01 }


    # Auto Update
    # 00 AU disable (default)
    # 01 AU enable
    # 02 AU auto
    # 03 AU enable with ua,sa and ga filter !!!!! always use this !!!!!
    A: { 03 }


    # Key Update
    # 01 update only new keys, default setting
    # 02 update all keys (used for valid PMK checking)
    U: { 01 }


    # Hash pids
    # 00 hash all pids, DO NOT USE THIS OPTION, IT IS ONLY FOR TESTING STUFF
    # 01 hash only pids with implemented algos and available keys !!!!! always use this
    H: { 01 }


    # Key files folder
    # 00 keyfiles in /var/keys
    # 01 keyfiles in /var/tmp
    T: { 00 }


    # On Screen Display for the Multysystemcam on com1/com2
    # 00 No OSD (default)
    # 01 display Smartcard messages in Neutrino
    # 02 display Smartcard messages in Neutrino new nhttpd format
    # 03 display Smartcard messages in Enigma
    # 04 display Smartcard messages in Enigma2
    O: { 00 } 192.168.0.3 coolstream


    # Logger and NET-mode UDP port Init
    # 00 do not init UDP port
    # 01 Init UDP port for IP, port, UDP
    L: { 00 } 192.168.0.251 7025


    # demux, multicam/comport configuration
    # example: yz = 0x0A = 00001010 (use com2 with inverted CTS detection line)
    # *x ** ; x = device nummber to be used (0= default)
    # D* ** ; force use of /proc/bus/gtx for cw write operations
    (in the dbox2 the gbox writes directly the CWs, 00 is the
    recommended mode ! No drivers are required) use D* ** ONLY if
    you have Problems. 0* ** should be prefered !!!
    # F* ** ; write CWs in both devices (used for PVR in STB04xxx devices)
    # ** y* ; y=0001b (0x1*) use slot1 as Multicam (only on STB04xxx)
    # ** y* ; y=0010b (0x2*) use slot2 as Multicam (only on STB04xxx)
    # ** y* ; y=0011b (0x3*) use slot1 and slot2 as Multicams (only on STB04xxx)
    # ** *z ; z=0001b (0x*1) use com1 as Multicam
    # ** *z ; z=0010b (0x*2) use com2 as Multicam
    # ** *z ; z=0011b (0x*3) use com1 and com2 as Multicams
    # ** yz ; yz=00110011b (0x33) use slot1+slot2+com1+com2 as Multicams
    # ** *z ; z=0100b (0x*4) invert CTS detection on com1
    # ** *z ; z=1000b (0x*8) invert CTS detection on com2
    #V: { 00 10 } #Slot 1
    #V: { 00 20 } #Slot 2
    #V: { 00 30 } #Slot 1+2
    V: { 00 3F } #Slot 1+2+SC8in1


    # RS232 SSSP mode
    # x debug messages, 1=on, 0=off
    # y com port to use (0=none, 1=com1, 2=com2)
    R: { 00 } 9600


    # Task type
    # 00 ** normal mode gbox mode (no season, use Multicam instead)
    # 01 ** Season Emulation in a Irdeto allcam chid 0602 nonZ
    # 10 ** Season Emulation in a Irdeto allcam chid 1702 nonZ
    # 11 ** Season Emulation in a Irdeto allcam chid 1702 Z
    # 12 ** Season Emulation in a Irdeto allcam chid 1722 Z
    # 13 ** Season Emulation in a Irdeto allcam chid 1762 Z
    # ** *1 Com port to use for season emulatiom (1 or 2)
    # ** 0* Use CTS for RST detection
    # ** 1* Use DCD for RST detection
    # ** ** 9600 = Baudrate to be used (working only on dbox2)
    W: { 00 00 } 9600


    # =============================================================================
    # extra options to override default setting in case you expirience Problems,
    # normaly these setings are not required.


    # Files, folders, devices
    # folder/device comment
    #F: { 01 } /var/tmp/pmt.tmp // pmt file
    #F: { 02 } /var/tmp/emm.info // key update log file
    #F: { 03 } /var/tmp/ecm.info // ecm info file
    #F: { 04 } /var/tmp/atack.txt // atack info file
    #F: { 08 } 1 // pmt mode (0 - pmt file mode, 1 - pmt socket mode)
    #F: { 11 } /var/keys // folder for config files
    #F: { 12 } /var/tmp // folder for temporary file
    #F: { 13 } /var/tmp // folder for keyfiles
    #F: { 21 } /dev/null // ca device
    #F: { 22 } /dev/null // dvr device
    #F: { 23 } /dev/null // demux device
    #F: { 31 } /dev/null // second ca device to write cw's (recording)
    #F: { 41 } /dev/sci0 // STB04xxx slot1
    #F: { 42 } /dev/sci1 // STB04xxx slot1
    #F: { 43 } /dev/tts/0 // rs232 com1
    #F: { 44 } /dev/tts/1 // rs232 com2
    F: { 43 } /dev/ttyUSB0 // rs232 com1# f�r externen Cardreader an com1 SC8in1 oder MCR 4/8 oder Smargo
    #F: { 44 } /dev/ttyUSB1 // rs232 com2# f�r externen Cardreader an com2 SC8in1 oder MCR 4/8 oder Smargo


    # For overclocking freaks, Clocking internal STB04xxx slots with:
    # 1=7.80MHz 2=6.30MHz 3=5.25MHz 4=4.50MHz 5=3.94MHz 6=3.50MHz 7=3.15MHz
    # Irdeto works fine on 7.8MHz, all other fine on 6.30MHz or 5.25MHz
    # The Dream has not a clean clock signal, some cards that are sensitive will
    # refuse to work even on 3.5MHz, thats why 3.15MHz is the default value there.
    # On other STB04xxx recievers the same cards work with 6.30MHz
    # Ist nicht Aktiv geschaltet ,also keine Funktion
    #F: { 51 } 02 // irdeto
    #F: { 52 } 03 // seca
    F: { 53 } 03 // viaccess
    #F: { 54 } 03 // nagra
    #F: { 55 } 03 // crypto
    #F: { 57 } 03 // conax
    #F: { 58 } 03 // nds


    # force a name change of the season or sssp rs232 device
    #F: { 45 } /dev/ttyS1


    # set stay alive ping time in seconds (default is 300)
    #F: { A0 } 300


    # disable direct serial port I/O access on 80x86cpus (win and linux)
    # direct port i/o is used to set unusual Baudrates, if you want to
    # a 3.579MHz card in a 6.000MHz reader etc ...
    #
    # Enabled (A1=0) is the default setting, has always been !!!
    #
    # Disable (set to 1) it ONLY if you have problems with ioperm or you want
    # to use a usb-to-rs232 smartcard reader
    F: { A1 } 1


    # descrambler selection by camd.socket private descriptor (0 - index mode, 1 - mask mode), mask mode is default
    #F: { AA } 1

    MfG sodex
  • Danke Sodex,
    ist doch sehr aufwändig, habe das Problem anders lösen können
    VU+ Ultimo mit 20 LNB T90 8°W bis 31,5O 85er für 39°,42°,45° O, 85er für 22,5, 24,5 u 30°W, 65er für 12,5W, 110er für 28,2°O