Unfortunately it's happeing again, with v13.0.2 too: Box don't Deepstandby !

    Diese Seite verwendet Cookies. Durch die Nutzung unserer Seite erklären Sie sich damit einverstanden, dass wir Cookies setzen. Weitere Informationen

    • Unfortunately it's happeing again, with v13.0.2 too: Box don't Deepstandby !

      The box is keep on restarting instead of Deepstandby !

      Tested Deepstandby in the morning/afternoon several times ... All was OK until now.
      I don't have any clue why. I rechecked all my setups ... looks all OK to me. Picture attached.

      Is it only with me?
      Is there some sort of conflict with a certain plugin ???

      Please help.

      Thanks
      Bilder
      • screenshot_2017-12-21_19-42-19.png

        530,55 kB, 1.920×1.080, 25 mal angesehen
    • :D
      Well, it just RESTARTS ... however I try to shut it down, by RC or Menu, it restarts !

      Btw, I was scared a bit whether it was happeing for a hardware problem ...
      because in the last few days I did many many times GUI restart as I was editing/testing the skin.
      Fortunately, I can confirm you that it is not the case, because I've just tested it by downgrading to 11.0.2 ... ALL OK THERE.
      So it must be something with the VTi v13x and some plugin config perhaps !?

      Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von hgdo () aus folgendem Grund: unnötiges Komplettzitat entfernt

    • Do a clean install and then work from there.

      Fragen zu einem Kraven Skin?
      Lies zuerst die FAQs
    • That's what I did all day today and then this happened at the end :)

      Well, guess what guys ... after restoring several backups: 11, 13.1 ... and now the 13.2 ... all could & can Deepstandby again !!!
      Just day before yesterday with v13.0.1 ... the box had the same Deepstandby problem.

      So why it was happening ? And it was happening continuously ?
      Is it because the box got too HOT ... needed a few secs to cool down ?
      My average temp of the box usually 30°C to 35°C maybe. Is it normal or too hot?

      If I remember correctly, while it was happening with the v13.0.1 a couple of days ago,
      I think, it did happen again in the next morning when the box obviously cold,
      that's when why I decided to go back to v11.

      So I'm a bit confused still as to why it happened and is it gonna happen again !?
      Dateien
      • Temp.png

        (4,49 kB, 102 mal heruntergeladen, zuletzt: )

      Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von hgdo ()

    • Is "immidiate shutdown" correct for Deepstandby?

      Maybe the pressing on the button isn't correct (long/short)

      Try to go into shutdown using the menue button - what will happen?
    • genius5000 schrieb:


      My average temp of the box usually 30°C to 35°C maybe. Is it normal or too hot?

      Thats room temperature in a good summer. What will you do then? Stack ice blocks on your box?

      Fragen zu einem Kraven Skin?
      Lies zuerst die FAQs
    • I think in summer it doesn't go more than 35°C. I dunno :P

      At the moment RPM is 190 ... should I go full speed in summer?
      What is your speed anyway?

      jo.wind schrieb:

      Is "immidiate shutdown" correct for Deepstandby?

      Maybe the pressing on the button isn't correct (long/short)

      Try to go into shutdown using the menue button - what will happen?
      Yes, I did that too many times, same result.

      Bus as you also read by now, it's working normally again.
      Wondering still why or can it happen again !

      Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von hgdo ()

    • Room temp: 23°C
      Box temp: 39°C
      Fan: 1400 rpm

      I am using the "Fan Control 2" plugin.

      In summer It is typically like:

      Room temp: 30°C
      Box temp: 45°C
      Fan: 2500 rpm

      Fragen zu einem Kraven Skin?
      Lies zuerst die FAQs
    • Merry Christmas

      I am experiencing another new problem related to the Deepstandby ...

      This time, everything works fine excepting when I want to start the box from Deepstandby it won't react by RC.

      Usually the light on the box blinks if any button is pressed on RC, but that doesn't happen either now.


      I was pretty scared again whether if it's a hardware issue ... thankfully it is not!

      Because, I just tried with the VTi 11 (restored) ... all fine there with Deepstandby Start/Off.


      It must be something in the VTi config I did ... anyone has any clue what perhaps?



    • @RickX

      In the das the box doesn’t react to the remote control... how does it look?
      NO IT DOES NOT, THE DEEPSTANDBY WHITE LIGHT STAYS SOLID (NO BLINKING)

      The box is in Deep Standby?
      YES

      The white LED is on?
      YES ON, BUT NO BLINK BY RC PRESS.
      ALSO, I MUST ADD HERE THAT WHEN THE IS ON AGAIN (BY THE BACK ON/OFF SWITCH),
      IF I PRESS ANY BUTTON SHORT/LONG, THE WHITE LIGHT REMAINS OFF!

      Do you use the original remote control?
      YES, PIC ATTACHED. THE OTHER ORIGINAL WITH METAL JOG WAS BROKEN.
      IT WAS REPLACED WITH THIS.

      Did you change the code of the remote control?
      NO, I NEVER INSTALLED THAT RC CODE CHANGER APP.
      Bilder
      • RC.jpg

        461,15 kB, 434×1.182, 4 mal angesehen
    • Are you sure the box is in Deepstandby? try to ping it or do a ssh-login/ftp-login. If one of these tries give a positive result, the box didnt shut down to Deepstandby, but crashed before reaching it.
      you can use the (very) long press powerbutton (>10seconds, sometimes 20 or more seconds).
      after it starts again, switch on debug log and if it hapens again check the log or upload it here to have someone look at it.

      btw: PLEASE DO NOT SHOUT, use lowercase!
      ACHTUNG!!!! Hier folgt eine Signatur:


      Die Benutzung der Suche ist NICHT verboten! D:

      "Hilfe!!!" ist kein sinnvoller Titel für einen neuen Thread, ebensowenig "VU+Zero" oder vergleichbares.

      Keine Hilfe ohne ausgefülltes Profil!
      Kein Netzwerksupport bei manueller IP-Adress-Vergabe :-)
      Kein Support bei portforwardings/ Portfreigaben

      Profil extra angepasst für die arme Emma, die sonst nichts im Leben hat :happy1:
    • @GaborDenes

      Definitely some very smart methods of testing true Deep Standby mode (for the next time).
      But, I am almost positive that the box was indeed on Deep Standby mode as the white indicator light was ON.

      Where do I activate the debug log please?

      Meantime though when I restored from v11 to v13.2 ... switching ON from Deep Standby is possible and working normally again !
      I haven't got a clue how/why it happened ... you the experts perhaps can guess?
    • actrivat debug.log:

      Menu -> VTI -> Settings -> System
      Page 2
      ACHTUNG!!!! Hier folgt eine Signatur:


      Die Benutzung der Suche ist NICHT verboten! D:

      "Hilfe!!!" ist kein sinnvoller Titel für einen neuen Thread, ebensowenig "VU+Zero" oder vergleichbares.

      Keine Hilfe ohne ausgefülltes Profil!
      Kein Netzwerksupport bei manueller IP-Adress-Vergabe :-)
      Kein Support bei portforwardings/ Portfreigaben

      Profil extra angepasst für die arme Emma, die sonst nichts im Leben hat :happy1:
    • @GaborDenes

      Thank you.

      Found it on Page 5 though.
      Please take a look at my setup in the pic. Is it OK?
      I ask, because I do not have much knowledge about it.

      There are several options under "Debug type" : On, e2-core, e2-python (I took On)
      Also several options under "Enable debug log" : Console, File, File (loop), Console & File, Console & File (loop) (I took Console)


      And In which location path the log txt file is saved?
      Bilder
      • screenshot_2017-12-25_13-44-30.png

        893,39 kB, 1.920×1.080, 5 mal angesehen
    • debug.log ist stored in /media/hdd
      Debug type ON
      Flie loop

      not console
      ACHTUNG!!!! Hier folgt eine Signatur:


      Die Benutzung der Suche ist NICHT verboten! D:

      "Hilfe!!!" ist kein sinnvoller Titel für einen neuen Thread, ebensowenig "VU+Zero" oder vergleichbares.

      Keine Hilfe ohne ausgefülltes Profil!
      Kein Netzwerksupport bei manueller IP-Adress-Vergabe :-)
      Kein Support bei portforwardings/ Portfreigaben

      Profil extra angepasst für die arme Emma, die sonst nichts im Leben hat :happy1: