another FBC setup question

affer · 7. Februar 2017, 15:40

Hello all

forgive my lack of knowledge

i have the following:

1 VU solo 4k with 2 FBC tuners

Tuner A goes with a single cable directly connected to unicable LNB on 1W
Tuner B goes with a single cable directly connected to unicable LNB on 5E

what should be the most correct settings in tunersetup on my VTI newest image, to get the possibilities to tune on more than one transponder?

thanks

//affer
Denmark

GaborDenes · 7. Februar 2017, 15:59

If you have got at least 4 unicable IDs per cable, you can configure 4 decoders per input.

affer · 7. Februar 2017, 16:26

i am not sure i understand how i should set it up, i have done the following

CH1 1210MHz (EN50494+EN50607)
CH2 1420MHz (EN50494+EN50607)
CH3 1680MHz (EN50494+EN50607)
CH4 2040MHz (EN50494+EN50607)
'above on Tuner a, i can only wath one transponderand i get nothing on Tuner B
ive tried with some different settings, but i am lost in the configuration possibilities.

should i try:

Tuner A
CH1 1210MHz (EN50494+EN50607)
CH2 1420MHz (EN50494+EN50607)
CH3 1680MHz (EN50494+EN50607)
CH4 2040MHz (EN50494+EN50607)

Tuner B
CH5 984MHz (EN50494+EN50607)
CH6 1020MHz (EN50494+EN50607)
CH7 1056MHz (EN50494+EN50607)
CH8 1092MHz (EN50494+EN50607)

or am i at the total wrong place ? i looked at Tunerkonfiguration Vu+ Solo 4K mit einem DVB-S2 FBC Dual Tuner und einem DVB-S2 Dual Tuner – Vu+ WIKI that does not help me much :-/

GaborDenes · 7. Februar 2017, 16:38

I dont have 2 LNBs but from my understanding you should use
(If you really got 2 unicable LNBs)

CH1 1210MHz (EN50494+EN50607)
CH2 1420MHz (EN50494+EN50607)
CH3 1680MHz (EN50494+EN50607)
CH4 2040MHz (EN50494+EN50607)
For tuner A
Setup Tuner A extended Unicable 1W SCR1
Tuner C extended connected to Tuner A SCR2
Tuner D extended connected to C SCR3
Tuner E extended connected to Tuner D SCR4
and
CH1 1210MHz (EN50494+EN50607)
CH2 1420MHz (EN50494+EN50607)
CH3 1680MHz (EN50494+EN50607)
CH4 2040MHz (EN50494+EN50607)
for Tuner B,
Setup Tuner B extended Unicable 5E SCR1
Tuner F extended connected to Tuner B SCR2
Tuner G extended connected to F SCR3

Tuner H extended connected to Tuner G SCR4

Then you can view/record 4 transponders at the same time per Satellite
VTI starts with SCR0 so adjust the settings accordingly

affer · 7. Februar 2017, 17:08

thanks, i will try this setup

and report back

and yes i have two Inverto Black Unicable Quad IDLP-QUDL42-UNI2L-1PP connected, one on each dish.

GaborDenes · 7. Februar 2017, 19:16

So in theory the setup should work. I have only one Unicable LNB and can not test it

affer · 8. Februar 2017, 19:32

This worked, thank you very much for your guidance, it i much appeciated.

thanks.